A water meter in a basement that keeps searching for a new connection on LTE-M drains its battery in a fraction of its planned lifetime. A tracker on NB-IoT loses its connection as soon as a truck switches cell towers during a data session. Both problems trace back to the same decision at the start of the rollout: choosing LTE-M or NB-IoT.
The two technologies are designed for devices that send small amounts of data over mobile networks, but differ in mobility, latency, coverage and power consumption. Whether a technology works in practice also depends on network availability per country, the supported frequency bands and the roaming agreements between operators.
What are LTE-M and NB-IoT?
LTE-M and NB-IoT are cellular Low Power Wide Area Network (LPWAN) technologies. They run on the 4G network of mobile operators and are designed for large-scale IoT projects where data communication is limited.
- LTE-M: for devices that move, communicate regularly or need to respond quickly.
- NB-IoT: for stationary devices that send small data packets from locations with a weak signal.
- Availability: varies per country and per operator.
- Hardware: many modern cellular modules support both technologies. The application and the network configuration determine which technology is used.
Why are IoT applications moving from 2G and 3G to LTE-M and NB-IoT?
Operators are gradually switching off their 2G (GPRS) and 3G (UMTS) networks to free up spectrum for 4G and 5G. Devices that have communicated over these networks for years will eventually lose their connection. Think of smart meters, alarm systems, payment terminals and industrial telemetry. Read the latest update on the 2G and 3G network sunset here.
For devices that send little data, LTE-M and NB-IoT are the logical successors. Applications that need more bandwidth are better suited to LTE Cat-1 or Cat-1 bis. Those categories are less optimized for power consumption and for coverage in hard-to-reach locations.
A migration requires more than a new SIM card. Modem, frequency bands, firmware and network compatibility must be aligned with the new technology.
How does LTE-M work?
LTE-M stands for Long Term Evolution for Machines and is also referred to as LTE Cat-M1. The technology uses a channel bandwidth of 1.4 MHz and reaches a theoretical maximum data rate of approximately 1 Mbps. The actual speed depends on the network configuration and the signal strength.
The biggest advantage is mobility. An LTE-M device switches cell towers during an active connection via handover, so a data session continues while the device moves. Thanks to its relatively low latency, LTE-M is suitable for applications that must respond immediately, such as an alarm notification. Where the operator supports it, voice via VoLTE is also possible.
The higher bandwidth makes remote firmware updates possible. With Power Saving Mode (PSM) and extended Discontinuous Reception (eDRX), power consumption stays low during the periods when a device is not communicating.
How does NB-IoT work?
NB-IoT stands for Narrowband Internet of Things and falls under the categories LTE Cat-NB1 and Cat-NB2. The technology uses a narrow radio channel of 180 kHz and is built for small data packets sent at fixed intervals. The data rate is lower than with LTE-M.
The strength of NB-IoT lies in coverage enhancement. By transmitting messages repeatedly, the signal reaches locations where mobile coverage normally falls short, such as basements, meter cupboards and underground installations. The narrow channel uses network capacity efficiently, which allows a single network cell to serve large numbers of devices simultaneously.
NB-IoT has no regular handover during an active connection. Latency is higher and can reach several seconds. For a sensor that reports a reading once an hour, that makes no difference. NB-IoT also supports PSM and eDRX.
What are the main differences between LTE-M and NB-IoT?
Mobility, communication pattern and network availability carry more weight in the choice than data rate alone. The table compares the technical differences side by side.
| Characteristic | LTE-M | NB-IoT |
| 3GPP category | LTE Cat-M1 | LTE Cat-NB1 / Cat-NB2 |
| Channel bandwidth | 1.4 MHz | 180 kHz |
| Data rate | Theoretically up to approximately 1 Mbps | Lower, depending on category and configuration |
| Latency | Relatively low | Higher, up to several seconds |
| Mobility | Handover during active connection | No regular connected-mode handover |
| Indoor and underground coverage | Good, depending on network | Extended coverage enhancement |
| Power consumption | Low with correct configuration | Very low with small, infrequent messages |
| Remote firmware updates | Suitable, including for larger files | Limited suitability |
| Voice | VoLTE possible if supported | No VoLTE |
| Roaming | Depends on operator, more widely available | Depends on operator, more limited availability |
How do PSM and eDRX work with LTE-M and NB-IoT?
With PSM, the modem enters deep sleep after sending data and the device is temporarily unreachable for incoming messages. With eDRX, the modem listens to the network at longer intervals. The device then remains reachable, with a delay that is set in advance.
Both functions only work if the operator supports them and the timers match the communication pattern of the device. A battery life of several years is achievable. Message frequency, data volume, signal strength and temperature determine the actual lifetime.
Which IoT applications suit LTE-M and which suit NB-IoT?
When is LTE-M the right choice?
- Track and trace: tracking vehicles, containers and mobile assets during transport.
- Personal emergency response: immediate alerts, optionally with voice functionality.
- Shared mobility: scooters and bicycles that report location and status.
- Mobile machinery: regular transfer of sensor data from changing locations.
- Firmware updates: devices that periodically receive larger software files.
When is NB-IoT the right choice?
- Water and gas meters: consumption data at fixed times, on battery power.
- Electricity meters: reading of metering data, with the meter itself connected to the grid.
- Parking sensors: detection of occupied parking spaces.
- Waste management: fill-level sensors in containers that periodically report their status.
- Building management: sensors in basements and technical rooms.
Can LTE-M and NB-IoT run side by side within one IoT project?
Yes. An organization might use LTE-M for mobile trackers and NB-IoT for stationary meters. Many cellular modules are dual-mode and support both technologies. Whether a device can actually switch between the two depends on the firmware, the configuration, the SIM card and the networks available at the location.
Do LTE-M and NB-IoT work in every country?
Availability varies per country and per operator. Some operators offer only LTE-M, others only NB-IoT. Frequency bands and network configurations also differ. A device that works via NB-IoT in the Netherlands has no guarantee of the same connection in another country.
With NB-IoT, roaming is the main point of attention. There are fewer roaming agreements for NB-IoT than for LTE-M. An international rollout on NB-IoT must therefore be validated per country in advance.
How do you set up IoT connectivity for an international rollout with LTE-M and NB-IoT?
- Define the communication pattern. Message frequency, data volume per message, mobility and the maximum acceptable latency determine the technology.
- Check the module per target country. Verify that the modem supports the LTE-M and NB-IoT bands used in each country.
- Test at the installation location. Measure coverage at the exact spot where the device will be installed, including indoors and underground.
- Align PSM and eDRX timers. Agree on the settings with the operator before devices are rolled out.
- Set up central management. Ensure visibility of data consumption and connection status, with the ability to adjust configurations remotely.
How does Thingsdata support international rollouts with LTE-M and NB-IoT?
Thingsdata is an independent value added reseller and is not tied to any operator. From a portfolio of more than 650 networks, we select, per country and per location, the operator that delivers LTE-M or NB-IoT with the right coverage and roaming agreements. With multi-network SIM cards, devices are connected in multiple countries without organizations having to arrange a separate connectivity solution for each country.
With Thingsdata Control, you independently manage your SIM cards and routers and gateways from different operators in one environment. Data consumption, connection status and configuration are centrally visible and adjustable there.
Which technology fits your IoT project?
Thingsdata determines per application and per country whether LTE-M, NB-IoT or a combination is the right choice. Thingsdata then selects the operator that delivers coverage at your installation locations and manages the connections via Thingsdata Control throughout the entire lifetime of your devices.
Contact us at +31-85-0443500 or info@thingsdata.com to discuss your rollout.
Need reliable IoT SIM cards? Request our test kit for 3 free SIMs with 100 MB data for 3 months. Experience seamless IoT connectivity today.
Looking for a reliable IoT partner? Download our brochure for instant access to valuable insights about our services and IoT solutions.